You dizzy because of computer problems, here will be discussed Solve computer hanging problem. Computers are often hangs certainly very annoying. When we're working our computer suddenly stopped in an instant. Computer hangs is very confusing, to do this you must know how to overcome computer hang. In this condition the computer was not able to function at all. To restore the computer to be way back then inevitably we have to press the Reset button, and unfortunately we have not had time saved jobs. Such events may have you experienced, or even now you're experiencing? Actually, many factors that can make the computer become slow or even hang. A discussion of solve computer hanging problem will begin. Everyone certainly want to know make computer faster.
Causes and solutions to solve computer hanging problem
Power supply problem
Know how to use computer is very important to solve this problem. With all the construction and the addition of new components in the computer power supplies will be disrupted. A power surge or spike can crash a computer as easily as a power outage.
SOLUTION: The solution is to use a UPS (uninterruptible power supply) just in case, if the power goes out or in case of power outage. If you want to know type of ups you could find its articles.
CPU (central processing unit) are usually equipped with fans to keep them cool. If the fan fails or if the CPU gets old, may begin to overheat and generate a specific error types. This is a common problem in chips that have been overclocked to operate highspeeds than they should.
SOLUTION: One solution is to replace the fan cleaned or new, clean the heat sink and care on a regular basis. Some special cooling fan / additional are available as well.
Fatal Exception OE VXD and ERROR
Fatal Exception OE and VXD errors are often caused by video card problems. This can be resolved easily by reducing the resolution of the video screen.
SOLUTION: Go to [Start]> [Settings]> [Control Panel]> [Display]> [-Setting]
Here you should slide the screen area bar to the left. Look at the color settings on the left side of the window. For most desktops, high color depth 16-bit is enough
BIOS settings problem
Errors or confusion in the BIOS can cause computer crashes. Every motherboard comes with a variety of chipset settings that are specified factory. A common way to access these settings is to press F1, F2 or DELETE key during the first few seconds during boot up. When this issues happened you must restarting my computer and know how to restart computer in the right way.
A common problem in the BIOS is the fault of the CAS latency. This refers to the RAM. EDO RAM (extended data out) that parents have a CAS latency of 3. SDRAM newer has a CAS latency of 2. Incorrect settings can cause the RAM the computer will lock up and crash. This is the answershow to make computer crash.
SOLUTION: Microsoft Windows is now better at allocating IRQ numbers than any BIOS. If possible stick with the position of the IRQ numbers to Auto in the BIOS. This will allow widows to allocate the IRQ numbers (make sure the BIOS setting for Plug and Play OS is switched to "yes" to allow Windows to do this).
The first sign of computer virus infection is not stable. Some viruses erase the boot sector of a hard drive making it impossible to start a program. Therefore it is a good idea to create a Windows start-up disk. Antivirus tips could help you know this issues. Notice how below.
SOLUTION: Create a start-up disk in a way: Click the [Start Menu]> [Control Panel]> [Add / Remove Programs] and look for the tab start up disk. Virus protection requires constant vigilance. A virus scanner is you need to be able to identify viruses. Virus scan results will be stored in a DAT file. DAT files should be updated weekly or monthly from your antivirus software sites.
A common cause of computer crashes is why the software is corrupted or bad installation process.
SOLUTION: Often the best solution is to uninstall the software and then re installing. If the problem is your Windows crashes, please go into boot in Safe mode and turn on computer in safe mode. This can be done during start up and when you see the message "starting windows" press F8 and it will take you to the Save mode. Safe Mode loads minimal drivers running. This allows you to find and fix problems that prevent Windows from loading at the time.
In the print-printing process, the act of sending a document to print creates a bigger file is often called file postcript. Printers have only a small amount of memory called a buffer. This can easily give overloaded. Printing a document also uses quite a lot of CPU power which will slow your computer's performance. If the printer is trying to print unusual characters, then this is where the problems are very frequent. Sometimes printers are difficult to rectify due to the chaos in the printer buffer.
SOLUTION: A good way to clear the buffer is, unplug the printer for 10 seconds. Boot back to the printer after about 10 seconds (called a cold boot) and will restore the default settings of your printer.
HARD DISK DRIVES
Information on HARD DISK DRIVE to become piecemeal or fragmented will wear out over time of usage. It is good to defragment your hard disk every month to prevent computer crashes.
SOLUTION: Do a defragment your hard disk by the way: Go to [Start Menu]> [Accessories]> [System tool]> [Disk Fragmenter]. Follow the next command.
Another reason why Windows crashes is hardware conflict. Each hardware device communicates with other devices through an interrupt request channel (IRQ). It's very unique for each device. For example, a printer is usually connected internally on the keyboard usually uses IRQ7 and IRQ1.
If there are many devices, or if they are not installed properly, two of them may eventually be sharing the same IRQ number. When the user tries to use both devices at the same time, a problem will occur.
SOLUTION: How to check whether your computer has a hardware conflict is to check the Device Manager.
Open the menu [Start]> [Control Panel]> [System]> [Hardware]> [Device Manager]
Often if a device has a problem then a yellow exclamation mark will appear next to its description in the device manager.
The best way to solve this problem is to remove the device and reinstall it again. Sometimes you may need to find more recent drivers on the internet to make the device function properly. A source that I often use is www.driverguide.com.
Damage RAM (random access memory) will cause the screen to die with a message saying Fatal Exception Error. A fatal error indicates a serious hardware problem. Safe computer use to prevent this issues. Sometimes this may mean there are parts that are damaged and need replacement. But the fatal mistake by RAM may be caused by a mismatch of chips. How to check computer memory is very important to you and help fix this problem. For example, the mixing of 70ns (nanoseconds) with 60ns RAM will usually force the computer to run all the RAM at a speed slower.Computer development make RAM is very high. This will result in frequent crashes.SOLUTION: One way to solve this problem is to go into the BIOS settings and increase the wait state of the RAM. This can make it more stable. Another way to solve this problem is to rearrange the RAM chips on the motherboard, or open and put back in correctly. Then try to repeat the test the circumstances that caused the problem.
Thus an article on solve computer hanging problem . Hopefully this article can provide benefits to you and can assist you in overcoming Solve computer hanging problem.